1.d Which Command Is Used to Configure Ipv6 Static Routes

Tracing the route to 2001DB8ACAD2091 1 2001DB8ACAD21 1 msec 2 msec 1 msec. When configuring an IPv6 static route youll use the ipv6 route XXXXX XXXXX whereas the first IPv6 address in the static route statement is the network and the 2nd IPv6 address is the next hop in the transit path to reach that network.

6 2 1 Packet Tracer Configure Ipv4 And Ipv6 Static And Default Routes Answers

Demonstrate the floating static route is working.

. Creates a directly attached static route configured to send packets out interface fastethernet 00. Make sure to enable IPv6 unicast routing by using the Cisco IOS command ipv6 unicast-routing from the global configuration mode. Configure an IPv6 recursive static route to every network not directly connected to R1.

Just like with IPv4 it is possible to use an interface as the next hop. Static routing uses fewer router resources than dynamic routing. To delete a static route use the following steps.

Use the show ip route static command to print all static routes. Enable IPv6 routing on all routers. Use the ping command to ensure that R1s G001 interface is reachable.

Static routing is relatively easy to configure for large networks. Static Route can be configured by the following IOS commands. Enable IPv6 on global configuration.

Enter this command on each router. This will only work with point-to-point interfaces. Configure recursive static routes on R1.

Before configuring static routes we must configure the router to forward IPv6 packets Which command accomplishes this. Enable IPv6 routing on all routers. To configure a directly attached IPv6 static route use the following command format.

Static routing is more secure because it does not advertise over the network. Which command is used to configure an IPv6 static default route. Configure IPv6 Static and Default Routes.

This primary default route should be through router ISP1. On R2 configure a static default route via R1s G000 address. Configure a static route for R1s Loopback1 network via R1s G001 address.

We could type in if we wanted to 00000000 etc etc. Configure an IPv6 recursive static route to. Ipv6 route 0 interface next-hop5.

First issue the show ipv6 route static command. Ipv6 route default interface next-hop. Global command to define an IPv6 static route with packets forwarded out the local router interface listed in the command.

Lets configure that for IP version 6. Deleting a static route. Your job for this lab is to configure static IPv6 routes on R1 with some admittedly strange requirements all for the sake of getting a better understanding of what happens with overlapping IPv6 routes and administrative distance.

If you are familiar with Static Routes and Default Routes click the following link to view an introduction to Static Routes and Default Routes. R1 configipv6 route 2001DB82264 Serial 000. You also have the ability to assign the IPv6 static route an administrative distance the same way you would assign administrative distance.

Nicocisco replied 2 months ago. How to configure Static Routes. In this part of the activity you will configure IPv6 static default and floating static default routes for IPv6.

Before configuring the device with a static IPv6 route you must enable the forwarding of IPv6 packets using the ipv6 unicast-routing global configuration command enable IPv6 on at least one interface and configure an IPv6 address on that interface. Which command is used to configure IPv6 static routes. On Edge_Router configure a next hop static default route.

Configure an IPv6 static default route. For our example configuration we will use the topology below. In configuring an IPv6 static route we will use the same procedure and configuration syntax that we are using in configuring IPv4 static routes.

Ip route 00000 interface next-hop. R2 config terminal R2config interface g000 R2config-if shutdown R2config-if end. Austin configipv6 route 2001db8c18364 fastethernet 00.

In Cisco Routers IPv6 static routes can be configured using the following Cisco IOS command ipv6 route from Cisco IOS global configuration mode. The second was a host. Ipv6 unicast-routing Enter this command on each router.

R1 show ipv6 route static IPv6 Routing Table - default - 4 entries Codes. Configure an IPv6 floating static default route. Ipv6 route networkprefix exit interfacenext hop address i p v6 route network prefix exit interface next hop address Part 2.

Branchconfigipv6 route 0 Gi01 2001DB8D1A5C9002. I would use a default static route to get there. Creates a static route configured to send all packets to a next-hop address of 2001db8c1822.

Packet Tracer Lab with Static Routing Configuration. Routerconfigip route destination_network subnet_mask default_gateway administrative_distance permanent OR. R2config ipv6 route 2001db 8acad1064 2001db8acad11.

Ipv6 route 00000 interface next-hop. Looks funky it really does but that is our default route for IPv6. Its truncated thats all.

Configure recursive static routes on R1. A directly connected static route is normally used with a point-to-point serial interface. Before configuring static routes we must configure the router to forward IPv6 packets Which command accomplishes this.

Austin configipv6 route 2001db8c18364 2001db8c182264. Use the ping command to ensure that R1s G000 interface is. Routerconfig ipv6 route Recursive IPv6 Static Route A recursive static route is created when.

C - Connected L - Local S - Static U - Per-user Static route B - BGP R - RIP I1 - ISIS L1 I2 - ISIS L2 IA - ISIS interarea IS - ISIS summary D - EIGRP EX - EIGRP external ND - ND Default NDp - ND Prefix DCE - Destination NDr - Redirect O - OSPF Intra OI - OSPF Inter OE1 - OSPF ext 1 OE2 - OSPF. R1show ipv6 route static S 2001DB82264 10 via. Configure IPv6 Static and Default Routes Step 1.

Heres what the routing table looks like. Issue the shutdown command on R2 G000. You should see two.

The command to configure this route would be ipv6 route 2000102128 3000122 100. Configure IPv6 Static and. Static routing scales well with expanding networks.

Note down the route you want to delete. Ipv6 route prefixlength outgoing-interface next-hop-address Global command to define an IPv6 static route with both the next-hop address and local router outgoing interface listed.

Ipv6 Routing Static Routes Explained And Configured Study Ccna

Ipv6 Static Routing Networkacademy Io

How To Configure Ipv6 Static Route

Implement Static Routes For Ipv6 Configuration Example Cisco